Clarke CL300M Spezifikationen

1OPERATING & MAINTENANCEINSTRUCTIONS300mmVARIABLE SPEEDMETAL LATHEModel No. CL300M1008CLICK HERE TO VIEW / BUY CLARKE SUPPLIES FROM M&P

10Fig. 3Tool 1 Tool 2ATHE SADDLEThe Saddle carries the Cross-Slide (6), on to which is mounted the Compound Slide(7) with Tool Post (5), allowing intr

11UNPACKING & PREPARING FOR USEOn receipt, carefully unpack the lathe. Inspect to ensure that no damage wassuffered in transit and all parts are a

12INSTALLATIONCAUTION!DO NOT ATTEMPT TO USE THE MACHINE UNTIL INSTALLATION IS COMPLETED, ANDALL PRELIMINARY CHECKS HAVE BEEN MADE IN ACCORDANCE WITH T

13We strongly recommend that the machine is bolted firmly to a strong workbenchusing the tapped holes used to secure the feet to the lathe. This is to

14Check that all components are still secure and working freely and correctly.Check also to ensure the mountings are secure.Repeat the procedure at th

15OPERATIONA. SIMPLE TURNINGBefore starting the machine, as described above, it is imperative that the setup forthe type of work to be carried out is

16It may be necessary to adjust the position of the compound slide or reposition thework in the chuck to guarantee that there is adequate clearance.W

17B. SIMPLE TURNING WITH POWER FEEDThe same basic setup is used as described above, except that, before starting, theLeadscrew F/N/R Lever (25) is se

18C. BEVEL CUTTINGBevel cutting involves the use of thecompound slide, which is mounted on thecross-slide and set at right angles to it for allnormal

19The general procedure for screwcutting is as follows:1. Try to get as much distance from the chuck to the end of the proposed screwthread as possibl

2SPECIFICATIONSMotor ... 230VAC, 50Hz, 1 PhasePower Rating ...

20CHANGING GEARS FOR SCREWCUTTINGThe leadscrew is driven, via a gear train, by a gear on the spindle. The gear ratiowill therefore determine the rotat

21 Threads Gear Per Inch A B C D12 40 65 - 3013 40 65 60 3014 40 65 - 3516 40 65 - 4018 40 65 - 4519 40 50 60 5720 40 65 - 5022 40 65 - 5524 40 65 -

22In order to change the gears, ensure the machine is switched OFF and disconnectedfrom the mains supply.Remove the gear train cover which is secured

23MAINTENANCEFor maximum performance, it is essential that the lathe is properly maintained.BEFORE USEAlways inspect before use. Any damage should be

24To adjust the jib strip, to account for wear and ensure the slide moves evenly andsmoothly, proceed as follows:1. Slacken off all lock nuts and scre

25ACCESSORIESA range of accessories is available from your Clarke dealer which extends theversatility of your machine. These are as follows:1. Indepen

26Fig 15EXTERNAL JAWS - 3-Jaw ChuckTo change the jaws, insert the chuck key and open the jaws to their fullest extent. Itwill then be possible to remo

27 No. Description Qty Part No.1 Bed Way 1 HT300M0012 Chuck 1 HT300M0023 Spindle 1 HT300M0034 Screw M6x30 3 HT300M0045 Washer M6 3 HT300M0056 Nut M6 5

28Cont.83 Screw M6x12 4 HT300M08384 Wheel 2 HT300M08485 Knob 2 HT300M08586 Handle 2 HT300M08687 Dial 2 HT300M08788 Bracket 1 HT300M08889 Feeding Screw

29PARTS DIAGRAM

3TABLE OF CONTENTS PAGESpecifications ... 2Spare Parts & Servi

30WIRING DIAGRAM

31NOTES

32

4

5INTRODUCTIONThank you for purchasing this CLARKE 300mm Metal Lathe.The compact rugged construction and screw cutting capabilities, makes theCL300M id

6GENERAL SAFETY PRECAUTIONSFOR OPERATING MACHINERYCAUTIONAs with all machinery, there are certain hazards involved with their operation anduse. Exerc

718. DO NOT STAND ON THE MACHINE. Serious injury could occur if the machine istipped over. Do not store materials above or near the machine such that

8Fig. 1FEATURESLEGEND1. Headstock 15. Automatic Feed Lever2. Spindle Flange 16. Cross-Slide Feed Handle3. Chuck Guard 17. Apron4. 3- Jaw Chuck 18. Man

9THE HEADSTOCKThe motor provides a direct drive to the Spindle via an internal tooth type belt.Spindle speed is variable, and is regulated by the Spee