Clarke CTS10D Bedienerhandbuch

0900©Part Number 6500750Operating & MaintenanceInstructionsPRODUCT SERIAL/BATCH NO...10” TABLE SAWModel CTS10C

Loose parts in bags G Arbor Spanner. H Saw Blade Securing Nut Spanner I Handle (for Blade Height Adjuster Wheel)complete withM6 x55mm Cross Head Scr

ASSEMBLYBefore the machine can be used, the loose parts must first be assembled to it, and certainadjustments carried out. Please proceed as follows:

WARNING!NEVER START THE MACHINE WITH THE BLADE GUARD REMOVED. C. Rip Fence1. Remove and discard the shipping nut from the threaded rod on the front en

MOUNTING THE SAWIMPORTANTIf the saw is to be a permanent fixture, ensure it is sited in an area with adequateillumination and power supply.DO NOT plac

NOTE: For proper stability, holes must be counter sunk on the underside of the plywood so that screwheads are flush with the bottom surface of the mou

14 2. The Saw BladeCheck to ensure the blade is sound. If teethare chipped, or cracks are apparent, it mustbe renewed. 3. The Blade GuardEnsure the Bl

15Auxiliary FenceMake one using pieces of 10mm plywood and19mm hardwood. Fasten together with glueand wood screws. Dimensions are shown in Fig.12

16Additionally, when positioning the fence for maximum rip, make sure it is fully clamped,and does not extend beyond the edge of the table. Do not rip

17When the width of rip is 150mm (6”) and wideruse your RIGHT HAND to FEED the workpiece,use LEFT HAND only to GUIDE the workpiece,do not feed the

18 4. Crosscutting.Crosscutting is the term used to describe cuts made in timber across the grain. This type ofcut requires the use of the MITRE

1

19Notches are provided in the mitre gauge head forattaching an AUXILIARY FACING to make it easier tocut longer pieces. Ensure the facing does

WARNING!NEVER USE THE RIP FENCE AS A LENGTH STOP BECAUSE THE CUT-OFF PIECE COULD BINDBETWEEN THE FENCE AND THE BLADE CAUSING A KICKBACK. 6. Mitre Cutt

21 8. Compound Mitre CuttingCompound mitre cutting is a combination of mitre cutting and bevel crosscutting. The cut ismade at an angle other than 90O

22 2. Changing the BladeThis procedure is explained on page 10 under ‘Assembly’.IMPORTANT: 1. Use only Clarke Blade, Part No. 6503125.2. Replace the b

23 4. Adjusting 90 and 45 Degree Positive StopsWARNING!ENSURE THE PLUG IS DISCONNECTED FROM THE POWER SUPPLY BEFORE PROCEEDING4A. Adjusting Positive S

TROUBLE SHOOTINGTROUBLE PROBABLE CAUSE REMEDYSaw will not start 1. Saw not plugged in 1. Plug in the machine2. Fuse blown or circuit breaker 2.

PARTS LISTSRip Fence AssemblyMitre Gauge AssemblyBlade Guard AssemblyNo. Description Part No Qty1 Pin 14913301 12 Push Nut n/a 23 Anti-Kickback Pawl

1 Label n/a 12 Screw Rod 1510021 13 Spring Pin n/a 14 Screw n/a 15 Handle 14008302 16 Nut Hex n/a 17 Hand Wheel 14900601 18 Knob 15100801 19 Flat W

PARTS DIAGRAM27

Thank you for purchasing your new CLARKE 10” TABLE SAW, which is designed for DIY, andhobby use ONLY.Before attempting to operate this machine, plea

SPECIFICATIONSModel No ...CTS10CPart No. ...6500750Motor ...

GENERAL SAFETY RULESWARNING!As with all machinery, there are certain hazards involved with their operationand use. Exercising respect and caution will

19. SECURE THE WORK. Use clamps to hold accessories when practical. It’s safer than usingyour hand.20. DON’T OVERREACH. Keep your proper footing and b

ELECTRICAL CONNECTIONSWARNING! THIS APPLIANCE MUST BE EARTHED.Connect the mains lead to a 230 volt (50Hz) domestic electrical supply via a standard 1

FEATURES7 1. The switch panel incorporates the ON and OFF switches, and an overload reset button.Your saw also features an Overload Protection device

7. The Rip Fence is for use when rip cutting timber. It can be easily moved or locked inplace by screwing IN the locking handle. Take care NOT to ov